Manitou Roto telehandler (MRT) rental: one machine for lifting, crane work and work at height

When you rent a Manitou roto telehandler, you get a forklift, a crane and an aerial work platform in one machine: the superstructure of the MRT series rotates through 360 degrees while the chassis stays in one place on its outriggers. Luibl Rental has ten MRT models in its rental fleet, with 4,000 to 7,000 kg load capacity and 17.90 to 34.70 m lift height.

On confined sites, every repositioning of a fixed telehandler costs time: retract the outriggers, manoeuvre, realign, set up again. On facades, halls and high-rise buildings with many load points, this adds up over the day. A roto telehandler serves the full circle around the machine from a single position. With the right attachment, it also takes on tasks that would otherwise require a mobile crane or a separate aerial work platform.

Image of a rental machine of type TSR-4018 | Manitou MRT 1840

TSR-4018 | Manitou MRT 1840

Lifting capacity
4.000 kg
Lifting height
17,90 m
Lateral reach
15,10 m
Dimensions
5,25 m x 2,39 m x 2,94 m
Drive unit
Diesel
Image of a rental machine of type TSR-4518 | Manitou MRT 1845

TSR-4518 | Manitou MRT 1845

Lifting capacity
4.500 kg
Lifting height
18,00 m
Lateral reach
15,20 m
Dimensions
7,26 m x 2,45 m x 3,04 m
Drive unit
Diesel
Image of a rental machine of type TSR-5021 | MRT 2150 Privilege

TSR-5021 | MRT 2150 Privilege

Lifting capacity
5.000 kg
Lifting height
20,60 m
Lateral reach
18,10 m
Dimensions
6,78 m x 2,43 m x 3,05 m
Drive unit
Diesel
Image of a rental machine of type TSR-6022 | Manitou MRT 2260

TSR-6022 | Manitou MRT 2260

Lifting capacity
6.000 kg
Lifting height
21,80 m
Lateral reach
18,20 m
Dimensions
6,97 m x 2,50 m x 3,10 m
Drive unit
Diesel
Image of a rental machine of type TSR-5025 | Manitou MRT 2550 Privilege

TSR-5025 | Manitou MRT 2550 Privilege

Lifting capacity
5.000 kg
Lifting height
24,70 m
Lateral reach
21,40 m
Dimensions
7,84 m x 2,49 m x 3,05 m
Drive unit
Diesel
Image of a rental machine of type TSR-7025 | Manitou MRT 2570

TSR-7025 | Manitou MRT 2570

Lifting capacity
7.000 kg
Lifting height
24,80 m
Lateral reach
20,50 m
Dimensions
7,67 m x 2,50 m x 3,10 m
Drive unit
Diesel
Image of a rental machine of type TSR-6026 | Manitou MRT 2660

TSR-6026 | Manitou MRT 2660

Lifting capacity
6.000 kg
Lifting height
25,90 m
Lateral reach
21,70 m
Dimensions
8,08 m x 2,50 m x 3,10 m
Drive unit
Diesel
Image of a rental machine of type TSR-6030 | Manitou MRT 3060

TSR-6030 | Manitou MRT 3060

Lifting capacity
6.000 kg
Lifting height
29,90 m
Lateral reach
25,70 m
Dimensions
7,94 m x 2,50 m x 3,10 m
Drive unit
Diesel
Image of a rental machine of type TSR-7035 | Manitou MRT 3570

TSR-7035 | Manitou MRT 3570

Lifting capacity
7.000 kg
Lifting height
34,70 m
Lateral reach
28,00 m
Dimensions
8,86 m x 2,50 m x 3,26 m
Drive unit
Diesel
Image of a rental machine of type Rotating Telehandler TSR-7035 ES | Manitou MRT 3570 ES

Rotating Telehandler TSR-7035 ES | Manitou MRT 3570 ES

Lifting capacity
7.000 kg
Lifting height
34,70 m
Lateral reach
28,00 m
Dimensions
8,86 m x 2,50 m x 3,26 m
Drive unit
Diesel
Mehr anzeigen

Ten Manitou MRT models cover 17.90 to 34.70 m lift height

Which Manitou Roto is right depends on the lift height and the load at the most distant placement point. The rated load capacity only applies close to the machine; as outreach increases, the permissible load drops significantly according to the load chart. Choose the model by the least favourable load point, not by the highest load capacity.

Up to 18 m lift height: compact for confined sites and courtyards

  • Manitou MRT 1840: 17.90 m lift height, 4,000 kg load capacity, 15.10 m outreach, 2.39 m wide
  • Manitou MRT 1845: 18.00 m lift height, 4,500 kg load capacity, 15.20 m outreach

21 to 26 m lift height: the class for building construction and installation

30 to 35 m lift height: for tall facades, industry and steel construction

All models are diesel-powered. The full data sheets are on the individual model pages.

Roto or fixed: a Manitou Roto pays off with many load points in a confined space

The Manitou Roto plays to its strengths where a fixed telehandler would have to reposition constantly. For pure material handling on open, level ground, a fixed machine is usually the more economical choice.

  • Rotating superstructure: The MRT models slew the load all around the machine. One position covers load points in front of, beside and behind the machine.
  • Outriggers: All MRT models have outriggers. They only reach full lift height and outreach when stabilised; this provides stability at great height but costs time with every repositioning.
  • Lift height: The MRT series starts at around 18 m and reaches up to 34.70 m. Below that, fixed telehandlers cover most tasks.
  • Space requirement: Because the chassis stays put, the Roto needs less manoeuvring space than a fixed machine that has to drive up to every load point.

If you mainly handle pallets on level ground, you will find suitable machines among the fixed Manitou telehandlers. An overview of all Manitou machine types is on the page Manitou telehandlers.

With attachments, the Manitou Roto becomes a crane or an aerial work platform

The roto telehandler changes its job by changing the attachment. Each attachment has its own load chart, which the operator must know before use.

  • Fork carriage and pallet forks: lifting material onto floor slabs, scaffolding and roofs or unloading trucks.
  • Load hook, winch and crane jib: The MRT works as a mobile crane and places loads over obstacles such as parapets or roof overhangs.
  • Work basket: With a basket approved for the model, the Roto becomes an aerial work platform for installation, facade work and maintenance at height.
  • Further attachments: We put together buckets and special grabs on request.

Which attachments suit your model is shown in the overview Attachments for telehandlers. Name the attachment you need in your enquiry, and we will plan machine and tool together.

Weight and outriggers decide whether the Manitou Roto suits your site

Depending on the model, a Manitou Roto weighs between 13,300 kg (MRT 1840) and 23,800 kg (MRT 3570). Clarify access, ground conditions and set-up area before you send your enquiry.

  • Access: The models are 2.39 to 2.50 m wide and 2.94 to 3.26 m high. Gates, passages and bends on the way to the set-up position must allow for this.
  • Ground: The outriggers transfer the load into the ground at specific points. On soft ground, backfill or above basement ceilings, load-spreading pads are needed; if in doubt, a structural engineer decides.
  • Set-up area: Allow space for the extended outriggers and the slewing range of the superstructure, and cordon off this area during operation.
  • Transport: We organise delivery by low-loader to your site throughout Slovakia. The low-loader needs a paved area for unloading.

Operators of a Manitou Roto need a qualification matching the rotating machine

Anyone operating a roto telehandler needs more than the basic telehandler qualification. In Slovakia, the applicable occupational safety rules (Act No. 124/2006 Coll.) and Government Regulation No. 392/2006 Coll. (work equipment) are decisive.

  • Basic qualification: It qualifies the operator to run a telehandler in forklift mode.
  • Qualification for rotating machines: Telehandlers with a rotating superstructure require an operator qualification matching this machine type in line with applicable Slovak safety rules and STN EN standards.
  • Qualification for basket and crane operation: Anyone working with a work basket or load hook needs a matching qualification for each of these modes. Personal fall protection equipment is used in the basket under Government Regulation No. 147/2013 Coll. (work at height).
  • Briefing and appointment: The employer briefs the operator on the specific machine and appoints them to operate it.

Luibl Rental does not offer training itself but informs you about certified providers. More on the Trainings page.

FAQ: Manitou Roto telehandlers

chevronDown

How high does a Manitou Roto telehandler lift?

Up to 34.70 m: that is the lift height of the Manitou MRT 3570, the largest Roto model in the Luibl Rental fleet. The smallest model, the MRT 1840, reaches 17.90 m. Load capacity ranges from 4,000 to 7,000 kg depending on the model; at great height and outreach, the permissible load according to the load chart is significantly lower.

What is the difference between a Manitou MRT and a fixed Manitou MT?

The MRT has a rotating superstructure, the MT does not. An MRT slews the load all around the machine and works from one position on its outriggers. A fixed MT only lifts forwards and has to be repositioned for every new load point, but it is usually more economical for pure material handling.

What qualification do I need for a roto telehandler?

You need an operator qualification matching a telehandler with a rotating superstructure, in line with applicable Slovak safety rules and STN EN standards. For work with a work basket or load hook, you also need a matching qualification for that mode. The employer briefs the operator on the specific machine and appoints them to operate it. Luibl Rental does not train operators itself but informs you about certified providers on its Trainings page.

Can a Manitou Roto be used as a crane?

Yes, with a load hook, winch or crane jib a Manitou MRT works as a mobile crane. Each of these attachments has its own load chart, and the operator needs the matching qualification. Name the attachment in your enquiry for this reason.

Can a roto telehandler lift people to height?

Yes, but only with a work basket approved for the specific model. Everyone in the basket uses personal fall protection equipment under Government Regulation No. 147/2013 Coll., and the operator needs a matching qualification.

How does a Manitou Roto get to the site?

By low-loader: we organise delivery to your site throughout Slovakia. The MRT models weigh between 13,300 and 23,800 kg and are up to 2.50 m wide. Clarify access, unloading area and ground bearing capacity in advance, and plan the job early so that machine and transport can be scheduled in good time.

Request a Manitou Roto telehandler: with these details we prepare your quote

The more precise your enquiry, the better our model proposal fits. These details help our dispatch team:

  • site location and rental period
  • required lift height and the heaviest load with its distance from the machine
  • attachments, for example work basket, winch or forks
  • access and ground conditions at the set-up position

You will promptly receive a quote with model, transport and attachments. Request a Manitou Roto quote now.